- First Post!
- TurboBob has checked in
- Aem?
- Commander 950 observations
- Looking for OTC 4000E Manual
- When is DFI actually needed?
- Tranlator settings
- Jay's chips
- What chip do I have ?
- Fast?
- delphi 80# chip
- Extender chip install
- Who makes a good chip?
- dfi and FASt boot up shortcut!
- translator setting question
- ????on knock & knock retard
- Accell DFI question on memory
- FAST wireing setup ??
- Anyone care to donate a 84# startup program ??
- Extender Chip Specs
- Any WinALDL users ?
- what chip for a low 10 gn
- AWSOME chip Eric (TurboTweak)
- Big Stuff
- Crank pulse width
- My SM results. Wanna analize?
- new chip advice
- Chip burning
- Extender and boost help (Bob?)
- Accel gen 6.23 Question
- Extender for 72# Siemans
- jc variable timing chip
- have at it
- BLM pegged at 160
- Emissions chip
- Where to start shopping?
- Fast VS stock ECM VS street VS strip
- JayC 93/94 octane chip
- TCC lock-up
- Burst Knock Retard - How important?
- So who's going to be the first to make a good scantool for PalmOS or PocketPC?
- Who sells Directscan?
- Eric
- Are their any spare ECM A/D channels?
- hELP WITH TUNING THE TRANS +
- Direct Scan problem With new PC
- Chip status
- Scanmaster 2.1 and TurboLink don't get along.....
- Scanmaster Died?
- Scan master abbreviations.
- ScanMaster upgradable?
- New Thrasher ?
- Extender Chip and TLink
- What causes MAF resets?
- Inj Constant and Fuel MAP
- BLM lock code patch
- Idle issues
- carchat
- Thrasher chip and DS
- Commander Chip Question
- TurboLink VehiclePak 11 available for download!
- Scanmaster Help Please!
- What chip to get??
- Wondering about a Kenne Bell Chip
- how do i build an aldl cable?
- Scanmaster 2.1 Questions
- Data logging with WinALDL?????
- Chip Sockets ECM FYI
- DFI load value
- Gen6 Wiring Harness Question....
- Awesome results with Eric's chip
- Turbolink questions.
- Official ICS (In Car Scantool) Picture thread
- Looking for T-Link Cable
- Innovative WB use with RPM record
- Anyone have any input on this AEM WB?
- Gen 7 Question
- Direct Scan fried my ecm, is it possible?
- Chip Reprograming To Correct VSS
- Bin file editor
- Atr's Chip
- Innovate LM1 gone nutty.......
- Innovate LM1 gone nutty.......
- Scanmaster problem...
- New Turbotweak chip
- commander chip
- Are there any Apple based scan tool programs?
- What changes are needed to the Prom, so I can read Timing on my Scan master II?
- Gen6
- boost/chip
- Plastic carrier's
- Eric(Turbotweak)Rocks
- what chip to buy
- Another FAST Wiring Question
- low speed fan
- OTC monitor 2000,Bad to run 1/4 with it?
- Thrasher Antitheft
- ~5 Yr Old JC93 octane chip timing?
- Logging peak boost with a Scanmaster
- WBO2 Extensions/connectors
- ALDL connection...
- Will Direct Scan work on my laptop?
- Direct Scan cable shield
- Intel 486 laptop help
- New Extender Chip
- direct scan cabel
- little off topic
- extender chip question
- Hot Air Chip options
- Kenne-Bell 9006U chip questions
- Who offers the Boost launch assist chip?
- ECU pin out for the waste gate solenoid
- Wow! Just put my TurboTweak chip in!
- i need a chip
- scan master
- Intro.....
- F.a.s.t
- recal a chip???
- JayC chip ID help
- question about maf for you TB guys
- Modded ecm?
- Lock up question
- Max Effort help..
- A/F and O2 help
- Code 15 Coolent Temp Sensor low
- Commander chip launch question?
- BLM's in direct scan
- Egt tuning question..
- Thrasher chip starting sequence
- JAY C chip question
- EPROM Carrier Part #
- Translator Pro Extender Pro chip and BOV
- Scan master readings HELP ASAP want to go to track :(
- TURBO TWEEK CHIP and Scan master readings HELP ASAP want to go to track :(
- Question for Eric
- Help with 60lbers -
- Extender Chip Question
- Scan Master II problems
- Scanmaster Readings Help
- scanmaster
- Strange problem with idle and O2’s
- Turbolink, Where are you?
- injector DC
- Code Warrior ?
- Chips
- scanmaster codes
- Help code 22 on scanmaster
- upgrading chip
- Scan Master Help
- lubrant chip 1st race and kicks serious butt
- Info Needed on chips/tuning
- Fuel Pressure Setting?
- The ECM's IAC Controls
- Turbolnk 4.0
- Eric
- whos chip
- Turbolink(need Info)
- Turbometer Pro Software
- modified ecm for high imp injectors
- Max Effort chip id help
- turbotweak question
- o2 millivolt ?
- New Turbo Tweak chip!!!!!!!
- chip for 6 speed conversion
- 165 ECM and 808 code ? Bruce ???
- new TT chip question
- comander chip?
- Translator Pro Question?
- Direct Scan
- IAC count 0
- Blowing chips
- Help With Tuning
- '84 Riviera T-type - Chip #5867DXP
- Scan Programs
- lubrant chip
- Timing @ Idle
- gen 2 maf pro....install and tuning
- MAF translator Gen II where to use/put the aux/window and Voltage trigger 4 pin?
- I NEED A scantool witch snap-on or witch OTC
- Scan master???
- Wanted: Operating Manual Pathfinder lll
- New Power Logger
- power logger aux input
- o2 sensor
- Maft Pro
- Fastest on ME-R
- marshall
- RJC or AILKY kit
- Info on stock 86/87 ECM
- FAST Classic seq